U ontvangt korting als reseller van WiMood.
|> € 0,00||> 0||€ 1.238,84|
Soundvision LEA Connect Series 352, 2-Channel, 350w, 70v/100v Amplifier, 1U.
Proprietary Smart Power Bridge - Smart Power Bridge allows users to bridge a channel to achieve double the power of that channel without sacrificing an amplifier channel.
Experts at a Distance - The LEA Cloud platform allows system design experts to support customers from a distance, without the need to visit job sites. Designers can tune and adjust audio systems remotely.
Technical Support via "Telepresence" - LEA Cloud technology allows support functions that used to require on-site visits to be carried out without someone physically being present at the venue.
Efficiency and Recurring Revenue Opportunities
- Add real-time monitoring into service contracts
- Amplifiers can tell when preventative maintenance is required before a failure actually occurs.
- Ability to do remote troubleshooting without having to put someone on a truck.
- Know what components go on the truck before being onsite reducing service call time and visits.
- Web Browser-based UI - works on any device with no software to download
- Direct LoZ and HiZ (70V or 100V) selectable per channel
- 3 Ways to Connect:
1.) Built in WiFi Access Point
2.) Connects to existing WiFi network
3.) Local Area Network Ethernet connection
- Highly Efficient Class D Output Stage for low AC Current draw
- 96kHz Analog Devices DSP with Input Routing, multiple 48dB/Oct crossover filters, 8 Parametric EQ filters, user configurable speaker limiters, and real time load monitoring
- Universal Switch Mode Power Supply with PFC. Operation from 100VAC - 240VAC +/-15%
- Analog fully routable inputs
- External I/O Port for Remote On/Off and fault monitoring
|Output Power (20Hz to 20kHz)||2 x 350 WRMS @ 4Ohm, 8Ohm, 70V, 100V (175W at 2Ohm)|
|Inputs||Balanced analog Inputs with user selectable 26 dB and 34 dB input sensitivity|
|THD+N||0.1% (20Hz to 20kHz)|
|Frequency Response||+/- 0.5 dB @ 4Ohm, 8Ohm, 70V, 100V, -2.5dB @ 20kHz at 2Ohm|
|Signal to Noise Level||105dB (20Hz to 20kHz referenced to 8Ohm)|
|Crosstalk||70dB (20Hz to 20kHz)|
|I/O Latency||1 ms DSP latency under any condition|
|Load Impedance||LowZ down to 2 ohms, 70V direct, and 100V Direct per channel|
|Amplifier Output Classification||Class D with Proprietary Smart Power Bridge Technology allowing bridged output functionality without sacrificing an amplifier channel|
|DC Offset||+/- 3mV|
|DSP Architecture||Analog Devices Sigma 96kHz DSP Processor with 32-bit Core with Sample Rate Converters|
|Input Matrix||Routable matrix; any input to any output with primary and secondary input priority|
|Crossovers||Up to 48 dB/Octave IIR Filters (Linkwitz Riley and Butterworth)|
|Parametric EQ||8 Band Parametric EQ per channel|
|Output Delay||100ms per channel|
|Output Protection||DC, VHF, and AC Mains Protection, Overtemp and Current Limiter, fan fault detection|
|User Adjustable Limiting||Peak Voltage and RMS Voltage|
|Load Monitoring||Realtime Load Monitoring and Pilot Tone Detection from Internal or External Sources|
|Network Connectivity||WiFi or 100MB Ethernet with PoE or Built in WiFi Access Point (IEEE 802.11b/g/n WPA, WAP2, WEP) Operating Frequency: 2412 - 2472MHz ; Channel Spacing:5Mhz ; Modulation: DSSS, OFDM|
|User Interface||Web Browser User Interface or 3rd Party API control (Q-Sys coming soon)|
|Supported Operating Systems||MAC, iOS, PC, Android|
|Event Reporting||User Downloadable and Viewable Event and Fault log - POE allows for enhanced error monitoring|
|External I/O||External I/O In: Toggles Remote On/Off, External I/O Out: Indicates Amplifier Health|
|Cloud IoT||Cloud-based IoT functionality|
|AC Mains||100VAC - 240VAC +/- 15% 50Hz or 60Hz|
|Temperature||Storage: -20C to 90C - Operating: 0C to 60 C|
|Power Supply||Universal Switch Mode Power Supply with Power Factor Correction (No PFC in 84, 164, 88, & 168)|
|Safety Approvals||UL, CSA,CE, ETL, FCC, CCC, KETI, NOM , ROHS, PSE|
|Dimensions (L x W x H)||14.25inch x 19inch x 1U (362mm x 482mm x 1U)|
|Cooling||Front to Rear Variable Fan Speed Cooling, Fan Noise at idel is 50dB @ 1m, Fan Noise at 50% is 57dB @1m, Fan Noise at full speed is 63dB @ 1m|
|Connectors||Analog Input: 3 pin Amphenol Anytek, Output: 2 pin Amphenol Anytek, External IO: 3 pin Amphenol Anytek, Power in: IEC, Ethernet RJ45 In for Control ***Note: 84, 164, 8, & 168 do not have potentiometers on the rear panel|